The Johnson Blog

Ramblings of a geek with a few hobbies…

Category: wood turning

  • Lantern Accent Lamp

    Lantern Accent Lamp

    Ana and I have been taking glass blowing classes together, for the past year, at the Springfield Art Association. Our instructor, Jason LaBonte has been an incredibly patient, knowledgeable, and enthusiastic teacher (go check him out!)

    This project began after we learned how to make a “fishbowl” one evening. I had been trying to think of ways to come out of the class with a keeper, ideally somehow mixed with woodworking. That project immediately brought to mind a small desk/accent lamp.

    First, let’s take a quick look at the final result. Build photos to follow.

    Lantern Base

    This started with a good chunk of cherry wood, roughly 4″x4″x14″, if I recall correctly. I cut the piece in two and set aside half for the future lantern “top”.

    I don’t have a photo of the “plans” I drew up, but the difficulty in the base revolved around boring holes of varying diameters and depths to support holding an E26 lamp:

    Source: https://www.amazon.com/dp/B0G69LTL11

    First up was to turn the half-blank round, and add a good sized tenon to use larger set of jaws in hopes of reducing vibrations later.

    After flipping it around, I began the boring process.

    I’m bad at taking the time to get all of the photos, but about an hour later, it looked as follows 🙂

    Flipping yet again gave me access to attach to smaller jaws and bore from the other end, and finish the bottom.

    Not shown is the groove I also put in the top, inside which I plan on embedding half a threaded ring pair so I can screw in the glass globe (with the other half of the threaded ring pair glued on).

    Globe

    And that’s where the project sat for a little while. Not intentionally. Everything was looking good, the glass globe I made in class looked like it was going to fit great. It was 10:45pm and I was done for the night, when I accidentally dropped said globe directly onto my table saw – I swear it exploded in a hundredth of a second.

    To say I was furious is a massive understatement. While I’m glad things didn’t get thrown in the basement, boy was I close. I don’t have a photo of what that globe looked like, or the aftermath. I’m glad for that right now.

    Fast forward a few weeks, and I (with Ana’s assistance) finally got a replacement globe blown. It’s a better shape, though the colors were more prominant on the original. That’ll teach me.

    Lantern Top

    Now with a replacement globe back in hand, I could proceed with making the lantern top. I threw the other half of the original cherry wood onto the lathe and got to work.

    As you can see, I burned in a par of lines and also took the risk of messing the whole thing up by using the texturing tool to add some knurling. I don’t know why, I thought it would look cool. And I think it does.

    Tung Oil

    Both the base and the top are finished with 100% tung oil. 3 coats.

    Putting It All Together

    I affixed the threaded rings (3d printed, purchased from Amazon) to the base and the globe. In the base I used CA glue. On the glass I used GE Silicon 2 glue. Verdict: the rings are a good idea, but I should have cold-worked the glass to produce a truely flat bottom on the globe. As is it doesn’t fully screw into the base due to a slight obstruction – but it does its job of preventing the glass from falling off and breaking.

    I also routed a small groove for the power cord. And finally, hot melt glued the top onto the globe. I opted for hot glue here because it was easier to use than the silicon. Though the first attempt didn’t fully take because of the aforementioned oil. Attempt 2 is under way after a light sanding of the inside of the top with 120 grid sandpaper – hopefully to give the glue something to hold onto. To be determined.

    Flicker Bulb

    Rather than a regular, low-lumen LED bulb, I opted for a “flickering” model which looks a bit like a dancing flame.

    So that’s it. It’s sitting on my desk here at home, providing a nice little glow to the room – and I love it!

    It’s so satisfying to come up with an idea and turn the raw materials into something geniunely nice to look at, and useful at the same time.

  • Log to Bowl, Wood Unknown

    Log to Bowl, Wood Unknown

    Earlier this year I was able to get ahold of a few pieces of an unknown species of wood. I quickly rough turned them back in April and placed them in to paper bags with shavings to dry.

    Tonight I took one off the shelf, weighed it, and found it had stabilized. Ready to turn!

    There is a lot for the eye too look at, that’s for sure. There was a little tearout but not too bad. Polar water for scale 🙂

    I don’t know what kind of wood it is, so if you recognize it, let me know. Here’s what it looked like in log form.

    The new lathe is a pleasure to work on. Vibrations are greatly reduced and it simply does not bog down. It also has Reverse, which I’m finding very useful for sanding to a nice smooth surface.

    I have a few more of pieces of this wood and now I’m excited about what they’re going look like.

  • Dead Lathe; New Lathe

    Dead Lathe; New Lathe

    Last weekend I went to fire up the lathe to process some newly acquired logs and the lathe stopped lathing. Well, it spun but wasn’t happy about it. Lots of noise and heat, I just had to shut it down and say goodbye.

    Not thriled with the prospect of the cost of a full-size replacement (or getting one into the basement), I opted for another benchtop model. But this time I went with a Jet, one with a more powerful moter and about 60% heavier.

    Welcome to the Jet 1221VS!

  • Bottle Opener

    Bottle Opener

    Last year I received some curly cherry wood. It’s been air drying and over this long weekend I decided to give a small piece a turn.

    It’s great looking grain, for sure. I’m glad I have several more pieces and will be looking to use it on nicer items in the future.

    As far as the shape goes, I messed up a little while turning so it’s about a half inch shorter than intended. I think a longer neck will more closely resemble a beer bottle.

  • Cherry with Character

    Cherry with Character

    I rough turned this Cherry bowl several months ago and it has been drying in my basement since. I didn’t have high expectations for the finished bowl because it just looked a bit plain.

    Happily, this turned about to be incorrect – it has far more visual interest than I expected.

  • Wooden Passive Speaker

    Wooden Passive Speaker

    A friend sent a video to me a couple of days ago, showing someone making a “passive speaker” on the lathe – one of those horns (for lack of a better term) you place your phone into to amplify the sound.

    I’ve had a piece of Cherry sitting on my shelf for a couple of years now for which I just haven’t had the right project. This seemed like a great use.

    I started off with this piece, maybe 6″x6″.

    After 3.5 frustrating hours Wednesday night, I completed the shape – inside and out. It was an incredibly frustrating experience on my lathe, trying to hollow out the horn into end-grain, when the piece was this long and I don’t have any support other than this small chuck.

    20250702_2231461244237388226845160

    The next step, after work on Thursday, was the nerve-wracking step of taking a saw to this nicely shaped horn! It isn’t perfectly symmetrical, but is close enough.

    20250703_1925125393936861862348235

    It’s starting to actually look like a thing!

    The last piece was to flatten the bottom of the rear portion so it doesn’t roll. I adhered a sheet of sandpaper to some plywood and quickly ground down a flat bottom. Nice and stable.

    The best part, finishing, was done with a 1:1 mixture of pure Tung Oil and citrus solvent. I’ve applied one coat so far, and it’s looking great. Sounds pretty good too!

  • Larger (Cherry) Bowl

    Over the weekend I finally turned one of the Cherry wood blanks that has been drying in my basement for over 2 years now. The blank was on the larger side, and I didn’t want to waste a bunch of the wood, so I decided to try a taller bowl than usual.

    I think I found the limit, height-wise, of a piece like this on my lathe. It just caused too many vibrations and too many tool marks. To top it off, there were plenty of knots and soft-ish spots inside.

    Better luck next time.

  • Elm

    I recently turned a small Elm bowl/dish. The knots and cracks were a little bit of a challenge to deal with. I wanted to keep them in the final result so I filled them with dark brown CA glue.

    Decent results, lots of character to this one.

  • Honey Locust Bowl

    Honey Locust Bowl

    This week I wrapped up a pretty cool looking bowl. I believe it is Honey Locust, and it has some of the best looking grain I’ve ever encountered.

    I don’t often turn a bowl like this, a so called a natural edge bowl, but it made sense to do so with this wood. If only I had an actual use for it 🙂

  • Majestic Junior Fountain Pen

    Majestic Junior Fountain Pen

    I recently completed my first fountain pen, a Majestic Junior model from Penn State Industries. The wood is a piece of white oak from the Shawshank Tree, the tree at the end of the movie The Shawshank Redemption.